Rotate cylinder clockwise to align next chamber and repeat step 4 above repeat until all chambers are empty. KEEP FINGERS AWAY FROM TRIGGER, align chamber as shown in Figure 8, tilt revolver muzzle up and remove cartridge as it slides back out of the chamber.ĥ. KEEP REVOLVER POINTING IN SAFE DIRECTION AND DO NOT TOUCH TRIGGER.Ĥ. Be sure you are familiar with Safety Instructions in Section 3. IA CAUTION: ALWAYS EXCERCISE EXTREME CARE TO KEEP MUZZLE POINTING IN A SAFE DIRECTION, WELL CLEAR OF YOUR BODY, PARTICULARLY WHEN UNLOADING REVOLVERS THAT DO NOT HAVE EJECTOR RODS.ġ. Collect live ammunition for safe storage and empty cartridge cases for disposal.Ī 1 TO UNLOAD REVOLVERS WITHOUT EJECTOR RODS ![]() Lower hammer controlling its movement with your thumb, into Safety position.Ĩ. Squeeze trigger only long enough to allow hammer to move forward and clear Half-Cock notch, then release trigger completely so that the Safety notch can be properly engaged. With thumb firmly on hammer spur, draw hammer back slightly to disengage Half-Cock notch. Rotate cylinder clockwise to align next chamber with ejector rod and repeat step 4 above repeat until all chambers are empty.ħ. Allow ejector rod to return forward under its spring action.ĥ. KEEPING FINGERS AWAY FROM TRIGGER, align chamber as shown in Figure 8 and push ejector rod, (located under the barrel) backwards through cylinder chamber, forcing out the live round or empty case, which should be removed from revolver. (The cylinder is now free to rotate clockwise.)Ĥ. KEEP REVOLVER POINTING IN SAFE DIRECTION AND DO NOT TOUCH TRIGGER.Ģ. Be sure you are familiar with Safety Instruction in Section 3. For the home defender and criminals alike, it is an ideal, affordable weapon.įor more information on revolvers and other weapons, check out the links below.1. And since they are made with a relatively small number of parts, they are relatively inexpensive to manufacture. Everything fits together so well that the guns very rarely jam. The enduring popularity of revolvers is due to the simplicity of their design. On the battlefield, the revolver can't possibly stand up to modern automatic weapons. But revolvers seem very limited next to newer technologies: The shooter must pull the trigger for every shot and stop to reload regularly. A shooter can load six shots at a time and only needs to pull the trigger to fire. Obviously, a revolver is easier to use than a flintlock or a percussion-cap weapon. The advantage of cocking the hammer first is that the trigger moves more easily when it is time to fire. In double-action revolvers, the shooter can either pull the trigger to cock and fire or pull the hammer back ahead of time. To reload, the shooter can place individual cartridges into the chambers or load six at once with a speed loader (basically, a small metal holder with cartridges secured in the right position).The extractor grabs the base of the spent shells and removes them from the cylinders. To reload the gun, the shooter swings the cylinder out and pushes on the ejector rod to operate the extractor in the middle of the cylinder.All of the expanding gas pushes forward rather than backward. The gas pressure also causes the cartridge case to expand, temporarily sealing the breech. The gas pressure drives the bullet down the barrel. The propellant burns, releasing a large volume of gas.The sequence of events in each shot is very simple: ![]() In modern revolvers, simply pulling the trigger will force the hammer backward and then release it. In early revolvers, a shooter had to pull the hammer back before each shot and then pull the trigger to release the hammer. Extending the barrel also increases the speed of the bullet, since the gas pressure accelerates the bullet for a longer period of time. A longer barrel improves stability, since it spins the bullet for longer. The inside of the barrel is lined with spiraling grooves, which spin the bullet to give it stability. ![]() The primer explodes, igniting the propellant, which drives the bullet down the barrel. The spring throws the hammer forward so it hits the primer. The basic idea of the gun is to cock the hammer back, line up a new cartridge in between the hammer and the barrel and then release the hammer by pulling a trigger. A spring-loaded hammer is positioned on the other side of the cylinder, in line with the barrel. In a modern revolver, cartridges are loaded into six chambers, each of which can be positioned in front of the gun's barrel.
0 Comments
Leave a Reply. |